Fiber Optic Patch Cord St-sc
Buy a CDW 1 Meter Multimode ST/SC Duplex Fiber Optic Patch Cable, 62.5/125 or other Fiber Optic Cables at CDW.com. The best source on the Internet for cabling and connectivity products: multimode fiber optic cable, custom cable assembly, fiber optic patch cable, fiber optic cable.
It's powerful and fast, fast, fast! First get to know the language - the 'jargon' - here's a list of terms you should get to know: Metric System: Fiber Optics, as a universal technology, utilizes the metric system as the standard form of measurement. Several of the more common terms: Meter: 3.28 Feet (3.28084 ft. To be precise). Kilometer: 1000 meters / 3,281 feet / 0.62 miles.
Micron: 1/1,000,000th of a meter. 25 microns equal 0.001 inch.
This is the common term of measurement for fibers. Nanometer: One billionth of one meter. This term is commonly used in the fiber optics industry to express wavelength or frequency of transmitted light. Let's Start With Fiber: Optical Fiber: Thin strands of highly transparent glass or sometimes plastic that guide light. Core: The center of the fiber where the light is transmitted.
Cladding: The outside optical layer of the fiber that traps the light in the core and guides it along - even through curves. Buffer coating or primary coating: A hard plastic coating on the outside of the fiber that protects the glass from moisture or physical damage. Mode: A single electromagnetic field pattern (think of a ray of light) that travels in fiber.
Multimode fiber: has a bigger core (almost always 62.5 microns - a micron is one one millionth of a meter - but sometimes 50 microns) and is used with LED sources at wavelengths of 850 and 1300 nm for short distance, lower speed networks like LANs. Singlemode fiber: has a much smaller core, only about 9 microns, and is used for telephony and CATV with laser sources at 1300 and 1550 nm. It can go very long distances at very high speeds. Both multimode and singlemode fiber have an outside diameter of 125 microns - about 5 thousandths of an inch - just slightly larger than a human hair. Plastic optical fiber (POF): is a large core (about 1mm) multimode fiber that can be used for short, low speed networks. POF is used in consumer HiFi and starting to be used as part of a new standard for car communication systems called MOST (go to For more on optical fiber, go. Terms that describe fiber optic cable: Cable: Fiber needs protection to survive all the places it gets installed and it's the cable that provides it.
Cables may have from one to hundreds of fibers inside. Jacket: The tough outer covering on the cable. Cables installed inside buildings must meet fire codes by using special jacketing materials. Strength members: Aramid fibers (Kevlar is the duPont trade name) used to pull the cable. The term is also used for the fiberglass rod in some cables used to stiffen it to prevent kinking.
Armor: Discourages rodents from chewing through it. Termination: Connector: A non-permanent device for connecting two fibers or fibers to equipment where they are expected to be disconnected occasionally for testing or rerouting. It also provides protection to both fibers. (Parts for an ST connector are shown.) Ferrule: A tube which holds a fiber for alignment, usually part of a connector Splice: a permanent joint between two fibers Mechanical Splice: A splice where the fibers are aligned created by mechanical means Fusion Splice: A splice created by welding or fusing two fibers together Fusion Splicer: An instrument that splices fibers by fusing or welding them, typically by electrical arc. Hardware: Terminations and Splices require hardware for protection and management: patch panels, splice closures, etc. Here's more on. Fiber Performance Specifications Terms you use when you want to take your measurements: Attenuation: The reduction in optical power as it passes along a fiber, usually expressed in decibels (dB).
Microsoft Visio is a great diagramming software but it is pricey. Visio Alternatives: 10 Best Diagramming Software. Visio Alternatives: 10 Best Diagramming Software. Bee visio planning software. An inexpensive alternative to Microsoft Project, PlanBee is a powerful yet inexpensive critical path project management and planning software tool able to produce. PlanBee, free and safe download. PlanBee latest version: Critical path project management planning tool. Learn how to create a project timeline in Microsoft Visio 2010. Use Visio 2010 for visualizing and presenting project schedules. CXO Software.
See optical loss. Bandwidth: The range of signal frequencies or bit rate within which a fiber optic component, link or network will operate.
Decibels (dB): A unit of measurement of optical power which indicates relative power. A -10 dB means a reduction in power by 10 times, -20 dB means another 10 times or 10 times overall, -30 means another 10 times or 1000 times overall and so on.
DB: Optical power referenced an arbitrary zero level dBm: Optical power referenced to 1 milliwatt Micron (m): A unit of measure used to measure wavelength of light. Nanometer (nm): A unit of measure used to measure the wavelength of light (meaning one one-billilonth of a meter). Optical Loss: The amount of optical power lost as light is transmitted through fiber, splices, couplers, etc, expressed in dB. Optical Power: is measured in 'dBm', or decibels referenced to one miliwatt of power. While loss is a relative reading, optical power is an absolute measurement, referenced to standards. You measure absolute power to test transmitters or receivers and relative power to test loss. Scattering: The change of direction of light after striking small particles that causes loss in optical fibers and is used to make measurements by an OTDR Wavelength: A term for the color of light, usually expressed in nanometers (nm) or microns (m).
Fiber Patch Cords
Fiber is mostly used in the infrared region where the light is invisible to the human eye. Terms that describe the tools you will need for installation and termination: Jacket Slitter or Stripper: A cutter for removing the heavy outside jacket of cables Fiber Stripper: A precise stripper used to remove the buffer coating of the fiber itself for termination. There at three types in common use, called by their trade names: 'Miller Stripper', 'No-Nik' and 'Micro Strip.' Cleaver: A tool that precisely 'breaks' the fiber to produce a flat end for polishing or splicing. Scribe: A hard, sharp tool that scratches the fiber to allow cleaving.
Fiber Optic Patch Cord Supplier
Polishing Puck: for connectors that require polishing, the puck holds the connector in proper alignment to the polishing film. Polishing Film: Fine grit film used to polish the end of the connector ferrule. Crimper: A tool that crimps the connector to the aramid fibers in the cable to add mechanical strength.
Terms that describe test equipment you will need: Optical Power Meter: An instrument that measures optical power from the end of a fiber Test Source: an instrument that uses a laser or LED to send an optical signal into fiber for testing loss of the fiber Optical Loss Test Set (OLTS): A measurement instrument for optical loss that includes both a meter and source Reference Test Cables: short, single fiber cables with connectors on both ends, used to test unknown cables. Mating Adapter: also called splice bushing or couplers, allow two cables with connectors to mate.
Fiber Tracer: An instrument that allows visual checking of continuity and tracing for correct connections Visual Fault Locator: A device that allows visual tracing and testing of continuity. Microscope: used to inspect the end surface of a connector for flaws or dirt.
The ST SC simplex single mode fiber optic patch cable use 9/125 single mode optical fiber, the cable length, cable diameter and colors are all optional. We supply ST SC fiber optic cable assemblies, these ST-SC fiber cables including single mode and multimode types, in simplex and duplex versions. Cables can be Rizer rated or Plenum rated, with LSZH cable and RoHS compliant cables available. We supply related standard and custom made fiber optic cables with competitive prices and fast delivery. The ST part of the cable is a bayonet style housing ST fiber optic connector.
It is with metal outer body and with a long spring loaded ferrule hold the optical fiber. ST Cable can be 9/125 single mode or 50/125 multimode or 62.5/125 multimode, in simplex or duplex versions. Connector ferrule interface can be PC, UPC or APC. ST is one of the older generations of connector, but it is still widely used in fiber optic communications, especially for multimode networks. The SC part of the cable is a high precision SC fiber optic connector. The connector is compliant to IEC, TIA/EIA, NTT and JIS specifications. It is with one piece construction and pulls proof design.
SC is low cost but high performance, which makes it one of the most popular cables. We supply the single mode 9/125, multimode 50/125 and multimode 62.5/125 types SC cables. They are with various PC, UPC, and APC connectors respectively. Our SC cables are available in simplex or duplex versions, with custom design available.